eMotors.ca and author of the article below cannot in any way be held responsible nor liable for any of the content or for any use or misuse of the information provided in the article. eMotors.ca and the author of the article cannot guarantee the accuracy or correctness of the information provided in the article, therefore, the information provided by the article can only be used at your own risk.

M44 Aluminum oil filter cover with pressure port

Author : eMotors.ca Inc Posted on : 26/11/2004
Model : BMW, 3 - Series (E36) 1991-99, 318i Category : Engine - Lubrification
 
O.E.M. oil filter housing cover, cast in aluminum with a threaded receptacle for an oil pressure gauge. It was included as standard equipment on the special edition E36 318is Class ll Motorsport Edition (homologated for the touring car championships). It was also an option in Europe for the E36 with M42 and M44 engines. Great for the street and track.

 

Pictures

Picture 1
Picture 2
Picture 3

Click on the thumbnails to see larger images.

 


Changing Your Engine Oil
Model : BMW, 3 - Series (E36) 1991-99 Category : Engine - Lubrification
... found that I let this take about 20-30 minutes for the oil to fully drain out. You will have to remove the jack stand while the oil is draining otherwise all of the oil may not drain out of the oil pan. Step 11. While the oil is draining, remove the oil filler cap. This will allow air into the oil reservoir and let it flow freer. Time Check: 0 hrs, 15 min Step 12. Now would be a good time to ... (more)
Posted : 27 October 2004 Author : Baden Smith
 
Complete Oil Pump Nut write up
Model : BMW, 3 - Series (E36) 1991-99, M3 coupe Category : Engine - Lubrification
... belt aside. It will be in your way later. Step 7: Unless you have room to get to the Power steering fluid resevoir, remove your intake and filter assembly. And...then, with a clean syringe remove as much of the power steering fluid as you can. DO NOT REUSE IT!! Step 8: Unbolt the Power steering pump and wire tie it to the radiator support beam or the engine brace (engine brace worked well for ... (more)
Posted : 28 October 2004 Author : Chad A.
 
Oil Change
Model : BMW, 5 - Series (E34) 1989-96 Category : Engine - Lubrification
... then loosen it by turning clockwise. Wipe the oil filter mounting, lubricate the new filter gasket with some fresh oil. Install filter by hand until gasket in contact with flange then turn the filter another 1/2 turn. Other engines: Loosen oil filter cover, prepare lots of rags around the filter housing. Remove the old filter and install the new one. Remove old O'rings and replace them with the ... (more)
Posted : 3 December 2004 Author : bmwe34.net
 
Oil And Filter Change
Model : BMW, 3 - Series (E46) 1998+ Category : Engine - Lubrification
... to the filter before I pull it out of the case. Once you have your bag ready pull the filter out of the case. Old Oil Filter Step 6: Cleaning Up Part I Its probably a good idea to wipe up the old, dirty oil out of the filter housing after the filter is removed. I use a shop towel to soak up the old oil and wipe out the rest of the case. I'm never shoot for spotless, just relatively clean. ... (more)
Posted : 14 May 2005  
 
Oil And Filter Change
Model : BMW, 3 - Series (E46) 1998+ Category : Engine - Lubrification
... plug. BE CAREFUL - The oil can be hot and scald skin. 12. When the oil has completely drained from the engine (flow has slowed to an occasional drip), replace the drain plug using the new gasket from the kit and tighten to 18 ft/lbs of torque. DO NOT over-tighten. If you're not careful, you can strip the oil pan and/or break off the drain plug. No fun! 13. Open the oil fill cap and add 6.5 ... (more)
Posted : 14 May 2005  
 
Browse by title :
# | A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z
Browse by make :
A | B | C | D | E | F | G | H | I | J | M | N | P | S | T | V