eMotors.ca and author of the article below cannot in any way be held responsible nor liable for any of the content or for any use or misuse of the information provided in the article. eMotors.ca and the author of the article cannot guarantee the accuracy or correctness of the information provided in the article, therefore, the information provided by the article can only be used at your own risk.
The content and the photos of this article are copyrighted and provided as a courtesy by

Receiver / Drier

Author : bmwe34.net Posted on : 02/12/2004
Model : BMW, 5 - Series (E34) 1989-96 Category : Interior - Heating and Air Conditioning
Source : http://www.bmwe34.net
 

The receiver/drier acts as a filter in the A/C system. It must be changed when the A/C system is opened for repair. There is two types of driers, one with 3 switches (Bmw E34 before 2/1989) and one with one switch (Bmw E34 after 2/1989)

It is located in the front right corner of the engine compartment below the headlight.



Procedure
System need to be discharged.
New O'rings.
Rachet, extensions.
New pressure switch if you have an E34 built before 2/1989
1. Discharge the system if not already done (Don't release it on the atmosphere PLEASE).. Remove the plastic cover at the back of the headlight. Remove the air filter box.
2. Disconnect the connectors from the windshield washer and move the windshield washer to the air filter box location. (You can also remove the washer pump and leave the air box alone).
3. Disconnect the connectors from the drier pressure switch(es). Remove the 3 screws holding the drier. Remove the drier and remove the pressure switch if E34 built after 2/1989.


Up to 1/1989 E34 ONLY

4. This is a picture of an old drier. You can see the separate high, low and intermediate pressure switches. The new ones use one switch.

Up to 1/1989 E34 ONLY

5. Cut off the two spades, splice then wire ends and solder them together. Use shrink wrap or electrical tape to isolate the wire.
6. Install the new pressure switch (or used one in case of an after 2/1989 E34) in the drier and install the drier back to its location. Connect the two A/C lines and use new O'rings. Tighten the 3 screws and connect the two connectors (black to black and white to white). Installation is reverse of removal
 

Pictures

Picture 1
Picture 2
Picture 3
Picture 4

Click on the thumbnails to see larger images.

 

References

  • http://www.bmwe34.net
    •  


    E36/5 Microfilter Replacement
    Model : BMW, 3 - Series (E36) 1991-99, 318ti Category : Interior - Heating and Air Conditioning
    ... the wire channel. I found it easier to get a nutdriver on the upper screw by removing the battery cover. The air collector now should be removed. This is the one part that's kind of tricky. It's a tight fit and a bit of a puzzle. By pulling the wire channel forward and moving the air collector from side to side while tipping it, the air collector will come out. Now visible is a thin plastic air ... (more)
    Posted : 14 May 2004 Author : Brian Brown
     
    Fan Blower
    Model : BMW, 5 - Series (E34) 1989-96 Category : Interior - Heating and Air Conditioning
    ... screws and pull the "sword" out. 6. Installation is reverse of removal. Procedure for SWORD repair You can recondition your sword, component cost is $3.52. You can purchase electronic parts from Mouser electronics (www.mouser.com), stock numbers are listed (no affiliation). (4) BUZ71A MOSFETS, type TO-220 mouser# 570-BUZ71A.(old part#: 511-BUZ71A) (thanks to Alun) N-channel, 50V, 13A (4) 8-32 x ... (more)
    Posted : 2 December 2004 Author : Drew Zacharda & Bill R
     
    Heater Valve
    Model : BMW, 5 - Series (E34) 1989-96 Category : Interior - Heating and Air Conditioning
    ... to fuse box on firewall) 3. Loosen all six screws on solenoid valve. 4. Tap on both solenoid valves with hammer while an assistant turns the drivers side temperature dial back and forth. 5. You should be able to hear the solenoid clicking now. 6. Tighten all six screws and replace plastic cover. 7. If this doesn’t work you may need to remove and clean the valves or perhaps replace them. 8. If ... (more)
    Posted : 2 December 2004 Author : Scott E.
     
    AFM Adjustment
    Model : BMW, 5 - Series (E34) 1989-96 Category : Interior - Heating and Air Conditioning
    ... at the connection. (round black connector). 4. Restart the car and before the catalytic converter gets hot (which it won't with the car just idling) insert the gas analyser in the tailpipe. 5. Adjust the AFF screw the the allowable tolerances, from 0.2 to 1.2. Bill's car is setup to 0.9 to 1.0 and it seems to give a better idle. It also helps get ride of a slight hesitation when accelerating. ... (more)
    Posted : 3 December 2004 Author : Bill R.
     
    R134a Retrofit
    Model : BMW, 5 - Series (E34) 1989-96 Category : Interior - Heating and Air Conditioning
    ... (Don't flush the compressor or drier). The rubber lines should be changed for barrier hoses also. Install the new port quick-disconnect adapters to the lines. The larger red one goes onto the high pressure side (line from the condenser through the sight glass to the expansion valve). The smaller blue one goes onto the low pressure side (line from the evaporator to the compressor inlet). With ... (more)
    Posted : 4 December 2004 Author : Bill R.
     
    Browse by title :
    # | A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z
    Browse by make :
    A | B | C | D | E | F | G | H | I | J | M | N | P | S | T | V