eMotors.ca and author of the article below cannot in any way be held responsible nor liable for any of the content or for any use or misuse of the information provided in the article. eMotors.ca and the author of the article cannot guarantee the accuracy or correctness of the information provided in the article, therefore, the information provided by the article can only be used at your own risk.
The content and the photos of this article are copyrighted and provided as a courtesy by

Stereo - Radio Alone

Author : Anton Ch. Posted on : 09/12/2004
Model : BMW, 5 - Series (E34) 1989-96 Category : Electrical - Radio
Source : http://www.bmwe34.net
 

Procedure courtesy of Anton Ch. and photos of Anthony

I believe the first step to improving the car’s sound system should always be the replacement of the head unit. My stock tape deck that came with my e34 was just plain horrible, an embarrassment to the BMW engineers. I did consider installing a cd-changer in the trunk but the inconvenience of getting out of the car to change cds was not a comfortable idea. Plus I was having a lot of other problems with the stock head unit such as very poor antenna reception; the speakers were making hissing noise at low volumes.

If you have an older E34, look at the bottom of the page as there is no harness connector for these BMW.


Procedure

DIN sized head unit (Advice when buying the head unit, make sure it matches the interior, amber or red on black)
Antenna adapter (Can be bought at circuit city for $11.99-P/N MET 40VW10)
BMW harness (Again at circuit city $15.99-MET 808590)
Tools!
For method 2 only:
Wire connector (electrical tape could be used as an alternative but this way holds the wires better; bought mine at Kragen $2.49-PA 6228654)
For method 1 only:
Head unit harness from Circuit City

There are two methods of doing this:
Method 1: Easy and a no-brainer, but will cost you $15 extra to buy a head unit harness (when you buy a BMW harness from Circuit City it has their own universal interface, then you pick and match another harness for you head unit which connects to the universal interface). Wire connectors are not necessary in this case. This is the plug and play method.
Method 2: This way is a little bit more complicated and will require about an hour worth of extra work, saves you money on the head unit connector.

1. The first step is to unplug the negative terminal from the battery. I found this a little bit tricky. The battery on the e34 is located underneath the rear bench. The simplest way to do it is to pull up really hard on the front edge of each side, lots of impulse here (don’t be afraid to use force if it does not let go right away), you should be able to pop up each side of the bench.
2. Then you want to remove the actual head unit. It is held by two pentagonal screw located under little flaps. You could buy the special tool or just use some hex wrench to do the job.
3. The head unit now should easily slide out. Disconnect the antenna. The tricky part is disconnecting the actual harness. On the head unit there should be a picture of how to do it with a screwdriver. Get a long flat head screwdriver and do it how it is on the picture. Don’t be afraid to use a lot of force, it may be really hard to move it. On mine it slid out easily for the first centimeter but then didn’t want to go at all.

Method 1 Only:
4. Simply connect the BMW harness from circuit city to the BMW and lock the lock. Then connect the Head unit harness from Circuit City to the head unit. Then connect the antenna adapter to the antenna and the head unit. Slide it in, connect the battery; you should now be able to enjoy your new head unit.
Method 2 only:
4. Please do not cut off the BMW’s original wiring to splice in the connections, its much better to just buy the harness and leave BMW’s wiring untouched. You probably noticed by now that BMW does not use (-) terminals for speakers. You will need to cap the (-) terminals and make sure they will never touch anything, connect only your (+) speaker wires.
Here is what you need to connect to what, all harnesses that you buy in a store use this EIA color standard (Over here in US at least), please note BMW uses some weird color-coding standard:
FRONT L(+) White to White
FRONT R(+) Gray to Gray
REAR L(+) Green to Green
REAR R(+) Purple to Purple
GROUND(-) Black to Black
Battery wire (+) Yellow to Yellow
Ignition Wire (+) Red to Red (read Amplifier part before splicing this connection)
Illumination Orange to Orange (please note my Kenwood calls this dimmer for some reason, but it means the exact same thing, so connect the Orange/White wire to Orange)
Everyone seems to be confused about the Amplifier wire. On the harness it should be Blue/White, if your head unit does not support power amplifier turn on (sometimes called Power Control wire), don’t worry. Simply splice it in with the Ignition wire. Both ways send +12v to the amplifier. The amplifier powers the power antenna.

If your head unit has motor antenna control wire or any other wires, don’t worry, BMW does need this wire. All unused wires should be capped with spare wire connectors so they do not touch anything else.

Now simply connect all the harnesses, antenna wires, slide the new deck in, connect the battery, and you should now be enjoying your new deck.

These are the BMW harness pin outs that correspond to the colors that BMW engineers used. I checked them out, it looks like they match the e34's harness:

FAQs:
1. Is it true that my stereo reception will be worse?
Never had problems with fm reception (sorry never listen to AM so not sure about that), in fact strangely my reception got even better. And yes I have the original stock in glass antenna.
2. For some reason my head unit is very quiet, even when I turn it all the way up it still sounds very quiet and hear a lot of hissing noise?
For some reason my Kenwood does this, I am guessing it has to do with the fact that the BMW amp is expecting 5 watts continuous. So what I had to do was use the fader, to fade signal to the rear or the front. Just make sure you slide it all the way to the rear or the front. Makes no difference if its front or rear, and yes the sound comes out from all the speakers front and back at 100% of what you would expect. Its just there is no way to fade front and back now with the new head unit.

If anyone has any questions regarding this article feel free to email Anton.


Older E34 wiring: Pictures courtesy of Martin Bacon

There is no harness for the older radios, so you will have to tap on the factory wires. Again, don't forget to connect the power antenna wire.
 

Pictures

Picture 1
Picture 2
Picture 4
Picture 5
Picture 6

Click on the thumbnails to see larger images.

 

References

  • http://www.bmwe34.net
    •  


    Installing Aftermarket Headunit (Alpine)/XM receiver/Alpine IPOD interface
    Model : BMW, 3 - Series (E46) 1998+ Category : Electrical - Radio
    ... headunit. It can easily be slipped up against the plastic panels without having to remove the panels. Remove these screws and take out this panel by disconnecting the connectors. under the steering wheel. Continue to run the AI-Net cable The AI-Net cable will need to be pulled from the gas pedal to the Headunit . I used a flexible Plastic piece that I attached to the AI-Net cable then pulled it ... (more)
    Posted : 29 October 2004 Author : stoneweed1
     
    BMW Stereo
    Model : BMW, 5 - Series (E34) 1989-96 Category : Electrical - Radio
    ... the amp and then 10 crossed over signals come out of the amp for the speakers. Antenna system (from antennaworld.com) All newer BMWs have the in-glass electronic systems by Fuba. The following information applies to these cars as follows: E31 - E32 - E34 - E36 and up These cars have 2 or 3 antennas in the rear glass, including one which is the defroster wires, all embedded or printed on the ... (more)
    Posted : 9 December 2004 Author : Tim T.& Peter W.
     
    Stereo - Subwoofer
    Model : BMW, 5 - Series (E34) 1989-96, M5 Category : Electrical - Radio
    ... Blue/Violet (Blue/Black) Rear Right (-): Blue/Grey (Blue or Brn/Orange) 5. You might need to strip some of the factory harness tape to allow enough play in the factory wiring to attach the big wire taps (or the splice). 6. You can use a short piece (around 8") of Left/Right RCA wire (RCA cable with individually insulated +/- wires as opposed to an RCA with the ground shield woven around the ... (more)
    Posted : 9 December 2004 Author : Derek I.
     
    BMW Radio Head Unit Installation
    Model : BMW, 3 - Series (E36) 1991-99 Category : Electrical - Radio
    ... break it. In order to install your new radio, you will need a BMW cable adapter (Figure 9). This adapter plugs into the factory connector and has leads on it that you can then connect to the leads or connector on your new radio (Figure 10). You can cut the OEM connector off and tap directly into the factory harness, but I strongly caution against this - it's best to use the adapter cable (cost ... (more)
    Posted : 18 May 2005  
     
    Headunit Replacement
    Model : BMW, 3 - Series (E36) 1991-99 Category : Electrical - Radio
    ... it. The wiring harness was a little difficult on mine, couldn't figure how to get it off. There is a small diagram etched into the end of the wiring harness (on the black plastic, you will be able to tell when you get the HU out). It shows that you should simply pull up on the black plastic and you're done. Mine wasn't just like that... You do pull up on the black plastic, but the top ... (more)
    Posted : 18 May 2005  
     
    Browse by title :
    # | A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z
    Browse by make :
    A | B | C | D | E | F | G | H | I | J | M | N | P | S | T | V