eMotors.ca and author of the article below cannot in any way be held responsible nor liable for any of the content or for any use or misuse of the information provided in the article. eMotors.ca and the author of the article cannot guarantee the accuracy or correctness of the information provided in the article, therefore, the information provided by the article can only be used at your own risk.
The content and the photos of this article are copyrighted and provided as a courtesy by

Headgasket Problems

Author : bmwe34.net Posted on : 09/12/2004
Model : BMW, 5 - Series (E34) 1989-96 Category : Engine
Source : http://www.bmwe34.net
 
A major problem with the Bmw E34/E32 especially the 3.5l and 2.5l is a headgakset failure caused by using unproper coolant (I always use BMW coolant) or overheating.


Engine suddenly overheats, radiator hose or heater hose explodes, a bubbling sound from the radiator overflow tank (may be a bad radiator cap), large bubbles in or foaming of coolant in radiator while engine is running, loss of coolant with no apparent leak, or persistent white smoke coming from exhaust are the first warning that the headgakset is going bad.

Visible warnings:
• Thick white smoke coming out of the tail pipe (water inside the cylinders)
• Coolant in oil (white residue on the oil cap or dip stick) or oil in coolant (stick your finder in the coolant reservoir and you will see)
• Mysterious loss of coolants without traces.
• Huge build up a pressure in the coolant circuit.
• Temperature gauge acting weird (the temperature gauge will get into the middle, and stay there for few minutes. Next, it will rapidly shoot for the “red” zone. It will do this in seconds. The moment the red zone is touched, the gauge falls just as fast to the middle, where it will stay for duration of the trip. Next day, same situation...)
When you first start your car leaking head gasket will introduce gas into the head cooling space. It will replace fluid from the area. The thermostat is closed so the gas has no place to go. The gas acts like an insulator so it will delay heat transfer to the thermostat. But other parts of the engine covered with the fluid blanket will heat the water up to the boiling point. Finally engine is hot enough to cause thermostat to open and let the gas go into the radiator. After the gas goes the overheated water and that's what causes your needle to rise on the gauge. Further operation is normal because thermostat is open and the gas goes to expansion tank as soon as it gets into the system. You need to repair the leak as soon as possible if that's the cause or you will end up with warped head due to spot overheating.

What test to perform to make sure:
• The first is a carbon dioxide test performed on the cooling system will tell you if C02 is going inside your coolant.
• A leakdown test will allow you to check each cylinder to look for pressure loss inside the cylinder. Failing the test could also be seepage past a bad valve guide, piston ring...
Head Gasket Testing Kit


The best method is to have a service shop, or a friend who owns a block test kit test your system for a compression leak to your cooling system. I heard that some test kits can be purchased from auto stores. This is a test unit and test fluid that changes color with the presence of exhaust gas in the engine coolant. Another test that should be completed is a coolant system pressure test Test your system for leaks with nine to twelve Psi pressure. It should not show any appreciable pressure loss within 5 minutes.

Sometimes it's worth it just to have a pro shop diagnose the problem, even if you are planning to do the repair yourself
 

References

  • http://www.bmwe34.net
    •  


    How to replace an E36 6-cylinder waterpump
    Model : BMW, 3 - Series (E36) 1991-99 Category : Engine - Cooling System
    ... 16mm or 8mm allen depending on model/year) and a breaker bar to turn the tensioner pulley bolt clockwise, slip the belt off of the pulleys. 5) Remove the waterpump pulley bolts, remove the waterpump pulley, remove the waterpump nuts. 6) Thread in M6 bolts in to the threaded lugs on the sides of the old waterpump. Tighten the bolts, they will push the old pump out of the block. Pitch the old ... (more)
    Posted : 26 October 2004 Author : Chris
     
    Fan Clutch Removal Mod
    Model : BMW, 3 - Series (E36) 1991-99 Category : Engine - Cooling System
    ... between the engine and the radiator, it may take a little force. Use a 10mm socket to first three bolts securing the thermostat housing to the engine. Then use a 13mm socket to remove the final bolt, that bolt also attaches an engine lift hook, remove the other bolt attaching that lift hook also and remove the hook. Pull the thermostat housing away from the block and, if you left the hoses ... (more)
    Posted : 26 October 2004 Author : Chris
     
    Changing Your Engine Oil
    Model : BMW, 3 - Series (E36) 1991-99 Category : Engine - Lubrification
    ... found that I let this take about 20-30 minutes for the oil to fully drain out. You will have to remove the jack stand while the oil is draining otherwise all of the oil may not drain out of the oil pan. Step 11. While the oil is draining, remove the oil filler cap. This will allow air into the oil reservoir and let it flow freer. Time Check: 0 hrs, 15 min Step 12. Now would be a good time to ... (more)
    Posted : 27 October 2004 Author : Baden Smith
     
    Installation of a '95 3.0L OBDI Intake onto a '99 3.2L OBDII Motor
    Model : BMW, 3 - Series (E36) 1991-99 Category : Engine - Intake
    ... picture, this is where the 5/8 tubing and tee fitting come into play. basically connect the tubing to the crank vent and the idle controller with the tee in the middle Now we have three more vacuum lines to deal with. The line that runs to the fuel pressure regulator (hard plastic line that runs towards the back of the motor will connect to the single vacuum fitting on the back bottom of the ... (more)
    Posted : 28 October 2004 Author : Midnight Autowerks
     
    M50 Manifold Install
    Model : BMW, 3 - Series (E36) 1991-99 Category : Engine - Intake
    ... in the bottom left, there is a hole that needs to be plugged. Well Bill found that a wheel bolt screws right in, so I cut it off to the right length, wrapped it in Teflon tape and screwed it in there: Random picture of me and my beloved engine: Ok, the next 2 pictures are of the plumbing and the brackets that the manifold mounts to. Now people have said that they bent them and that they ... (more)
    Posted : 28 October 2004 Author : John Doby
     
    Browse by title :
    # | A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z
    Browse by make :
    A | B | C | D | E | F | G | H | I | J | M | N | P | S | T | V