eMotors.ca and author of the article below cannot in any way be held responsible nor liable for any of the content or for any use or misuse of the information provided in the article. eMotors.ca and the author of the article cannot guarantee the accuracy or correctness of the information provided in the article, therefore, the information provided by the article can only be used at your own risk.
The content and the photos of this article are copyrighted and provided as a courtesy by

Fix A Sagging Glovebox Door

Author : Chris Posted on : 26/10/2004
Model : BMW, 3 - Series (E36) 1991-99 Category : Interior - Doors
Source : http://www.understeer.com/
 
Tired of your glovebox door sagging down and leaving a gap at the top? Of course you are! Here's a quick and simple way to fix it.

You will need the following:
- Hand drill
- A small drill bit
- Tape measure
- Small screws (#6 - 1/2" long or similar)
- Screwdriver


Open the glovebox. Along the top edge of the glovebox measure and mark spots 2 1/2" to the left and right of the latch. Using a drill bit that is slightly smaller than the treads of your screws, drill holes when you made the marks. Tighten a screw in both holes. The screws will clamp the glovebox tighter against the vent panel behind it.

Close your glovebox. Notice the lack of a gap. Slap your forehead for not doing this a long time ago! 8)
 

Pictures

Picture 1
Picture 2

Click on the thumbnails to see larger images.

 

References

  • http://www.understeer.com/
    •  


    Door Removal
    Model : BMW, 5 - Series (E34) 1989-96 Category : Interior - Doors
    ... the speaker. 6. Starting to pry the door panel off. 7. The panel is just about off. Note that the mirror cable was disconnected. The red cable is for the door handle. Make sure that you lift the door UP and OFF. 8. Another shot of the cable for the door handle. It simply comes right off. No real effort is required for this. 9. Peeling back the foam insulation to expose the power window motor, ... (more)
    Posted : 2 December 2004 Author : Scott Shackelford
     
    Door Microswitch Replacement
    Model : BMW, 3 - Series (E36) 1991-99 Category : Interior - Doors
    ... connector up by exterior door handle (red/white, red/green wires). Unclip wire bundles from holders and clip wire ties. 5) Remove door lock mounting screws with T-30 torx. See image below. 6) Reach inside the door and pull out the lock cylinder linkage rod from the lock unit. Then lift the unit up and off the door handle latch pin. See Bentley sec 515-2, fig 4 for a good illustration. Lock ... (more)
    Posted : 18 May 2005  
     
    Removing the door panel
    Model : BMW, 3 - Series (E36) 1991-99 Category : Interior - Doors
    ... Slide the door handle surround forwards (towards the joystick) and it will unclip. Prise the electric mirror joystick upwards using a blunt knife/screwdriver and unplug it. Starting at the bottom pull the door card outwards and work your way equally up either side and very carefully pull the top out towards you and off its retaining clips, then lift the entire door card up and free of the ... (more)
    Posted : 18 May 2005  
     
    Door Microswitch Replacement
    Model : BMW, 3 - Series (E36) 1991-99 Category : Interior - Doors
    ... connector up by exterior door handle (red/white, red/green wires). Unclip wire bundles from holders and clip wire ties. 5) Remove door lock mounting screws with T-30 torx. See image below. 6) Reach inside the door and pull out the lock cylinder linkage rod from the lock unit. Then lift the unit up and off the door handle latch pin. See Bentley sec 515-2, fig 4 for a good illustration. Lock ... (more)
    Posted : 18 May 2005  
     
    Door Hinge Replacement
    Model : BMW, 3 - Series (E30) 1983-93 Category : Interior - Doors
    ... to whatever BMW dealers may say. Buy a hinge assembly from a dealer. The bushing can not be bought without buying the entire assembly. I purchased mine from Foreign Motors West BMW in Natick, MA for $32 with my BMWCCA discount. Take the new hinge apart. Pull the C-clip and washer off the end with the flat screw head. Use a ratchet and remove the hex bolt from the other side. Use a punch and ... (more)
    Posted : 24 May 2005  
     
    Browse by title :
    # | A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z
    Browse by make :
    A | B | C | D | E | F | G | H | I | J | M | N | P | S | T | V