eMotors.ca and author of the article below cannot in any way be held responsible nor liable for any of the content or for any use or misuse of the information provided in the article. eMotors.ca and the author of the article cannot guarantee the accuracy or correctness of the information provided in the article, therefore, the information provided by the article can only be used at your own risk.

Steering wheel squeak FIXED

Author : Patrokloss Posted on : 01/11/2004
Model : BMW, 3 - Series (E36) 1991-99 Category : Interior - Steering Wheel
Source : http://www.bimmerforums.com
 
This might be a bit overdone for such a simple fix, but this question gets asked about twice a week so I figure it's time we had one of these. At any rate, the random squeaking noises when turning my steering wheel finally became unbearable. I couldn't really find a good writeup, so I tore into it and here's what I found.


As far as I can tell, there are only three things that can cause this noise. I would check them in this order:

1. Bearing at bottom of steering spindle
2. Bearing at top of steering spindle
3. Steering wheel slip ring

If you take your car to the BMW dealer with this problem, they will replace the slip ring, which will set you back about $300 and probably won't fix the noise... or it may actually seem to fix it for a week or two until it decides to come back. Speaking from experience on this one. Your best bet is to start with number one and work your way down.

Perform any of the following at your own risk. As always, follow basic common-sense safety procedures, especially when it comes to jacking up your car.

So here we go...

Steering Spindle Bearings


This is what the steering spindle assembly looks like. The lower bearing, number 7 in the diagram, is the most common cause of the squeak. The spindle itself is actually hollow, so even though the lower bearing is down in the engine bay below the firewall, any noise it makes will echo through the steering spindle shaft up into the car's interior. The result is a squeak that sounds like it is coming directly out of the steering wheel.

To lube the lower spindle bearing, you will need the following:

- floor jack and jackstands
- can of Tri-Flow or equivalent penetrating lubricant
- three flexible party straws (see pic)
- duct tape
- safety goggles

There's no good way to access the lower bearing, because it sits just below the firewall way up in the engine bay. In order to get to it, you're going to need to use the party straws and duct tape to fabricate about 18 inches of extra tubing attached to the end of the lubricant spray can.

I bought a package of thin party straws with flexible end segments at the local supermarket for $0.58. These work well because the very tip of your 18-inch tube will need to bend slightly in order to get a clear shot at the bearing. Get the thinnest, smallest diameter straws you can find:


Jack the front of the car up, support with jackstands, and wriggle under there until you see where the steering shaft exits the firewall. It's way up in there, at the top of this thing:


Shake the can of Tri-Flow or other lubricant up REALLY good... You need to build up some pressure in order for it to shoot all the way up there. Attach your extension and manuever it until the tip is pointed right at the steering spindle assembly where it pokes out of the firewall. Then, soak it! I recommend wearing some safety goggles while you do this... There's a good chance some of this stuff will drip down into your face.

Once that bearing assembly is good and drenched with lubricant, lower the car and take it for a drive. Do whatever you normally do that makes the steering wheel squeak... For me it was sharp low-speed turns like parking maneuvers. Listen for the squeak. If it's gone, great! If not, proceed to step two...



Next we'll tackle the upper spindle bearing and the slip ring. You will need:

- Bentley manual (not absolutely essential, but the photos make it a bit easier if you've never removed the steering wheel before)
- ball-point pen
- metric socket set
- T30 Torx key
- felt marker, ultra-fine tip
- more Tri-Flow or equivalent
- white lithium grease if you have it handy
- torque wrench

This procedure involves removing the airbag. PROCEED AT YOUR OWN RISK.

Break out your Bentley manual and follow the instructions to remove your driver-side airbag and steering wheel. It goes something like this.

Start by parking your car with the steering wheel centered and the front wheels pointed exactly straight ahead. Then:

1. Disconnect negative battery terminal

2. Remove lower steering column trim mounting screw and remove lower trim. The screw is at the very bottom of the underside of the steering column. Remove it and then remove the plastic trim piece that covers the bottom half of the steering column. You'll need to push your cruise control lever around to get the plastic piece out without breaking it, but it will come out.

3. Remove orange SRS connector from its holder and carefully separate connector. There's a tiny little tab you'll need to press in on the side... use a ball-point pen. The connector should slip apart.

4. Working behind steering wheel, completely loosen Torx screws (T30) while holding airbag in place. Support airbag to prevent it from falling out. These scews are a PAIN but they WILL come loose if you're patient.

5. Carefully lift airbag off of steering wheel and disconnect orange harness connector from rear of airbag unit. Mine just pulled straight off. Be careful to set the airbag down face-up, someplace out of the way.

6. Now remove the steering wheel center bolt, number 6 in the diagram. If I recall correctly you'll need a 17mm socket here.

7. Now you can see the tip of the hollow steering spindle through the middle of the steering wheel. The outer edge of the spindle is toothed where the wheel slides over it. Use an ultra-fine tipped marker or something similar to mark the exact position of the steering wheel relative to the steering column shaft; that way you can put the steering wheel back on in precisely the same position later.

8. Unlock steering wheel by turning ignition key on. Remove steering wheel.


Now you can see the top part of the steering spindle assembly. Break out your can of Tri-Flow and go to work. Give it several good shots and rotate the bearing and snap ring as you go to make sure the lube works its way in all around. Mop up excess.

On the back of the steering wheel you can see the slip ring. Give it a light coating of white lithium grease.


Now it's time to put everything back together:

1. Install steering wheel while aligning matching reference marks you made earlier. Make sure airback contact ring locking pin engages cut-out in contact reel. (See the Bentley manual for photos... The pin is white and plastic and fits into a small hole in the ring in back of the steering wheel.) Install steering wheel center bolt and torque to 46 ft-lb (63 Nm).

The rest is simply the reverse of removal: Re-attach orange harness connector to back of airbag. Replace airbag and tighten the two airbag mounting screws in back of the steering wheel. Re-attach the orange SRS connector. Replace lower steering column trim. Replace trim retainer screw. Re-connect negative battery cable. Then follow the normal procedure for re-activating your auto-up windows, radio code, etc. You're done.

Take your car for another drive and enjoy the squeak-free silence.


I've found this entire procedure also reduces steering effort and helps isolate the steering wheel from roadgoing vibrations. My guess is this will all have to be repeated every 50-70k miles or whenever the lubricant dries up again.
 

Pictures

Picture 1
Picture 2
Picture 3

Click on the thumbnails to see larger images.

 

References

  • http://www.bimmerforums.com
    •  


    Steering Fluid
    Model : BMW, 5 - Series (E34) 1989-96 Category : Interior - Steering Wheel
    ... 2 banjo bolts connecting the 2 hoses to it instead (one is larger than the other). Most of the fluids came out from the bigger bolt, not much from the smaller one. He managed to drain 24 ounces of fluid with this procedure. 535i 1. Remove fluid from the reservoir using the syringe. Place the pan under the car then remove the 19mm bolt holding the reservoir hose to the PS pump. (There is a 8mm ... (more)
    Posted : 3 December 2004 Author : bmwe34.net
     
    Steering Wheel
    Model : BMW, 5 - Series (E34) 1989-96 Category : Interior - Steering Wheel
    ... a bolt 17 or 19 i can't remember. to install E30/28 wheel you will need the small ring that's under the wheel or some other spacer, the E34 has one so find somthing about the same size and put it on top of the wheel under the 22mm nut and washer. the splines are the same size the end of the shaft is just a little longer Mtech 2 steering wheel (From Winfred): Get the spacer from under the m3 ... (more)
    Posted : 7 December 2004 Author : bmwe34.net
     
    Steering Wheel Retrofit & Upgrade
    Model : BMW, 3 - Series (E36) 1991-99 Category : Interior - Steering Wheel
    ... system. Most importantly, disconnect the negative terminal from the battery and wait at least 10 minutes for capacitors to discharge before beginning work. 2) Remove upper and lower trim pieces from around your steering column. Unplug orange airbag connector under steering column. 3) Using T-30 torx bit, release two retaining screws from behind airbag. Disconnect airbag and remove. Lie ... (more)
    Posted : 18 May 2005  
     
    Steering wheel squeak FIXED
    Model : BMW, 3 - Series (E36) 1991-99 Category : Interior - Steering Wheel
    ... drill on the bottom of the housing because the lubricant will drip out. Drill as far up the side as possible. Stick the lubricant straw in the hole and give it a 20 second squirt. The lubricant will saturate the bearings. I am now considering applying a thicker lubricant/grease. My car steers like new. Ken Gasper gasper11 View Public Profile Send a private message to gasper11 Send email to ... (more)
    Posted : 18 May 2005  
     
    E39 M-Sport Steering Wheel Retro-Fit
    Model : BMW, 5 - Series (E39) 1996-03 Category : Interior - Steering Wheel
    ... look and feel... Turn the steering wheel to the center, straight-wheels position. Extend the steering column outwards and driver's seat back for ease of access. 2. Be absolutely sure the battery is disconnected. Use the 13mm socket to remove the negative lead from the battery. 3. Loosen the (2) T-30 Torx bolts until the airbag is free. The 2nd pic is inaccurate since the wheel is not in the ... (more)
    Posted : 24 May 2005  
     
    Browse by title :
    # | A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z
    Browse by make :
    A | B | C | D | E | F | G | H | I | J | M | N | P | S | T | V