TJ Spacer lift
Model : Jeep, TJ Category : Suspension
... the small retaining clip on the bottom of the driver side coil (Fig 1.4) and the two nuts on top of each side of the sway bar. (Fig 1.5) With this complete, use the Hi-Lift to jack up the front of the vehicle and easily take the coils out. Remove the rubber bump stops by pulling down and working them back and forth. Loosen off and remove the 1/2 " bolt inside and the metal cup that held ... (more)
Posted : 19 May 2005  
 
Stretching YJ Wheelbase via Leaf Spring Swap
Model : Jeep, YJ Category : Suspension - Springs
... reverse Tie-rod Waggy springs on all 4 corners This does a few things: First it gets your tie-rod up and way out of the way of rocks and other things encountered on the trail. Secondly, it eliminates the possibility of the drag link hitting the tie-rod. This is a concern when moving an axle forward and using the stock steering set up, especially under hard compression. Another option that I ... (more)
Posted : 19 May 2005  
 
OBA Install
Model : Jeep, TJ Category : Suspension
... to being able to fill my tires after a trail run. You can see in this shot, the line of order after the compressor. The grey canister is the Kilby inlet filter which connects a 90 elbow then into the compressor which is to the right of this picture. On the outboard side is the stainless steel hose that comes out of the compressor to a 1/2"x3/8" brass reducing coupling into the ... (more)
Posted : 19 May 2005  
 
Fog Light Relay Bypass For the Jeep TJ
Model : Jeep, TJ Category : Lights - Fog Lights
... Any use of this article is at the readers own risk. This article may be freely copied provided the disclaimer is included and without alteration to it or the article....Peter Scott Remove glove box door assembly to expose Cut length and strip the 3 piece of wire and fuse panel -Locate the two relays and lift them crimp the small male slide connector on one up to unhook them from the clips. ... (more)
Posted : 19 May 2005  
 
Prepping / 1978 Wagoneer Front Dana 44 for a YJ
Model : Jeep, YJ Category : Driveterrain
... Been there…and I hate that snap sound! Once that was done, disassembly was quite easy. Disassembly I removed the chrome dust covers from the hub housing and could see the first retaining ring/nut, that was easy to remove by just using a flat head screwdriver and a mallet turning it counter clockwise. Once the nut was removed the drive flange and spring in behind it pops out, this puts ... (more)
Posted : 19 May 2005  
 
Borla Stainless Steel Header Install
Model : Jeep, TJ Category : Exhaust - Headers
... Fig 2.0 Fig 2.1 Fig 2.2 Once everything was cleaned up it was time to fit the new gasket for the Borla exhaust Header (Fig 2.1). There is two positioning pins that locate the gasket in place to ensure it is installed correctly see Fig 2.0. Once you have the gasket in place you can attach the Borla header (FIG 2.2) and hold it in with a bolt preferably in Bolt location #1 as this is one of the ... (more)
Posted : 19 May 2005  
 
Pinion Seal Replacement
Model : Jeep, TJ Category : Steering
... (if desired to help seal the sleeve Fig 1.4) and using the tool that is provided with the sleeve to lightly hammer the seal onto the Yoke (Fig 1.5 & 1.6) Fig 1.4 Fig 1.5 Fig 1.6 Fig 1.7 Fig 1.8 Fig 1.9 As shown in Fig 1.7 the complete Yoke ready for re-installation. Now that you are ready you will need to remove the seal from the pinion. You can use a big screw driver as shown in Fig 1.8 or ... (more)
Posted : 19 May 2005  
 
Skyjacker 4” lift install
Model : Jeep, TJ Category : Exterior
... Then firmly push the new bump stop into the cup. The lower stock control arms were also removed as well as the stock rear links. Now the new rear track bar relocation bracket in position and put the bolts in tight to hold the bracket into its mounting place. Now using a drill bit, drill the new hole as shown in (Fig 3.9) now the bracket was bolted on using the new bolts supplied in the kit. ... (more)
Posted : 19 May 2005  
 
Gas Tank Skid Install
Model : Jeep, TJ Category : Fuel System
... the fuel lines, wires, and filler hose connected (if you choose to do so), Slowly lower one side of the tank down (as seen in this picture), be careful not to lower excessively or pull on the tank to avoid putting adding stress on the fuel lines/wires, you do not want them to break!. Remove the tank straps out of the way, then remove the factory skid plate, prop the tank up so that it ... (more)
Posted : 19 May 2005  
 
AEV Rockrail
Model : Jeep, TJ Category : Exterior
... as you will need to do a bit more for the two holes closet to the fender flares as we will get to soon. Once the 3 bolts on the inner bracket are tightened we drilled the 4 holes out on the inner stabilizer bracket (Fig 1.4) Fig 1.4 Fig 1.5 Fig 1.6 Fig 1.7 Now that the inner bracket is secured it is time to fasten the two remaining bolts through the rock rail using special clips supplied with ... (more)
Posted : 19 May 2005  
 
3” Body Lift Install
Model : Jeep, YJ Category : Exterior
... side. This will allow you to unbolt it from our access flap.) Weld the nut to the bolt and grind a smooth surface where it broke off originally (fig6.6). Extract the broken bolt, fold down the flap and weld it shut. As a finishing touch, smooth out the weld and paint it to avoid rusting. fig7.1 fig7.2 fig7.3 At this point, all the body mounts spacers should be installed except the one at the ... (more)
Posted : 19 May 2005  
 
Browse by title :
# | A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z
Browse by make :
A | B | C | D | E | F | G | H | I | J | M | N | P | S | T | V