Lowering your C5
Model : Chevrolet, Corvette Category : Brakes
... the bushing. Cutting the bushing may make your ride a bit more harsh than before. (SKIP IF YOU DID NOT REMOVE THE BOLT) With the c-clip removed, loosen the top nut from the bolt. (SKIP IF YOU DID NOT REMOVE THE BOLT) Pull out the bolt and bushings from the leaf spring(the leaf spring is NOT under pressure). (SKIP IF YOU DID NOT REMOVE THE BOLT) Cut both bushings so that the section with the ... (more)
Posted : 9 June 2005  
 
LTFT / O2 Analysis & Tuning Guide
Model : Chevrolet, Corvette Category : Misc
... file provided here, you can crunch the data using the provided Excel template for a basic analysis. If you wish to sort the date on different columns, open up the file in a different worksheet, not in the template. To use the template: Start Excel, and open up the template youve saved to your computer. Select 'Data -> Get External Data -> Import Text File' from the menu. Browse to your log ... (more)
Posted : 9 June 2005  
 
Lidatek LE-30 Installation (B6 S4)
Model : Audi, S4 Category : Electrical
... opted to put it behind. The bumper support is hollow in the back--use a 5/16" nut as a spacer (not supplied) or tightening the bracket will deform the bumper. Mount the mating L bracket to the transponder with the back and right edges flush. I first put the double-sided tape in (adhesive not exposed) and held the bracket in place with duct tape to adjust the alignment. The tape should be in ... (more)
Posted : 7 June 2005  
 
LE-30 Install (B5 S4)
Model : Audi, S4 Category : Electrical
... steering column and behind the dash to the control unit, and replace the cover. Be very careful to note the positioning of the LED. See just to the right of it? That was a bad hole (JB Welded for now, I'll buy a new cover later). Drill through the part of the cover that has two layers. If you don't, the LED will bump into the plastic tab that's on the upper corner of the steering column. If ... (more)
Posted : 7 June 2005  
 
Low temp Thermo-Switch for S4 (B5) After-Run System
Model : Audi, S4 Category : Engine
... was a little hard to get out but eventually it just pulled out. When you first pull the thermo-switch out a little bit of coolant will escape. After the initial amount of coolant leaks out, no more will leak out. I didn't have a new o-ring so I re-used the existing one, seems to be working so far. The factory thermo-switch has a green body, the new thermo-switch has a blue body. Put the ... (more)
Posted : 7 June 2005  
 
Lower Grill Chrome Trim (A4)
Model : Audi, A4 Category : Exterior
... It comes with two 48" strips. 2) Remove the lower bumper center grill. It just pops out after pinching down 3 clips behind the bumper. Just pop the hood and use a flat head screwdriver to push down the contacts and slowly work the grill out. 3) Once the grill has been removed, use the knife to trim away the outer lip. The plastic is fairly soft. 4) Now you'll need to add some slots to ... (more)
Posted : 7 June 2005  
 
License Plate Bulb Conversion
Model : Audi, A4 Category : Exterior
... between the bolts which holds the trunk lock housing in place. 3) After the two bolts and two nuts have been removed unplug the license plate bulb housing connections and remove the from the trunk. 4) Looking at the rear of the handle you will see 4 torx screws. Using a 15T Torx screwdriver, remove the screws and pull the housing off of the handle. 5) Now, looking at the license plate bulb ... (more)
Posted : 7 June 2005  
 
Locking System Modification
Model : Audi, A4 Category : Interior
... to door lock 6. Unscrew the metal arm from the black connector on the lock housing. Once this arm is removed the door can no longer be manually unlocked. The key will still work in the door lock to unlock/lock the doors of the car. What this achieves The door is no longer manually unlocked by using the key in the door. Using the key in the door now tells the alarm system to activate the ... (more)
Posted : 7 June 2005  
 
Lower Engine Operating Temperature w/ Water Wetter
Model : Mercedes-Benz, S - Class, S500 coupe Category : Engine
... of the past. Aluminum is such an electroactive metal that it requires an impenetrable corrosion inhibitor film to prevent rapid corrosion. Acid neutralization capability is very important. Coolant which has been left in a cooling system for several years has probably become acidic from the oxidation of the glycol to acids. Also, keeping the glycol concentration in the cooling system ... (more)
Posted : 25 May 2005  
 
L-Jetronic engine management scheme
Model : BMW, 3 - Series (E30) 1983-93 Category : Fuel System
... :: Audio :: Body :: Brakes :: Cooling System :: Driving :: Electrical :: Engine :: Fuel System :: Interior :: Misc. & Useful Info :: Performance :: Specifications :: Suspension & Steering :: Transmission :: Troubleshooting :: Ventilation & A/C SHOW ALL SUBMIT ARTICLE Note: Be careful when using any of the procedures described on this section, and remember you'll be doing it at your own ... (more)
Posted : 24 May 2005  
 
Limited Slip Differentials on E30s (except 325iX)
Model : BMW, 3 - Series (E30) 1983-93 Category : Driveterrain
... will have in slippery conditions. It will also determine how much traction you have in corners where the inside rear wheel gets unloaded and almost airborne. It is nota good idea to have too much preload though, because itwill make the car understeer. The rear wheels will wantto run at the same speed, causing the car to run straight all the time.Do I have a LSD on my car?The diff housing has a ... (more)
Posted : 24 May 2005  
 
Lifting Points
Model : Ford, Focus Category : Misc
... Form >>> Screensavers >>> SVT Focus >>> TF Decals >>> TF Staff Directory Lifting Points CAUTION: The vehicle must not be lifted on the outer rocker panel. CAUTION: It is not recommended that the vehicle is jacked or lifted on the rear suspension crossmember. If the vehicle must be lifted on the crossmember, make sure that the jack or lift is positioned ... (more)
Posted : 20 May 2005  
 
Linear Rate performance Springs
Model : Ford, Mustang Category : Suspension - Springs
... the springs. Be careful not to lower the rear too much or you can break the rear brake line that sits at top of the differential case. NOTE: Remove the lower arm-to-axle pivot bolt and nut if the springs wont come out or use a spring compressor. Put the springs back in place. Now raise the differential to align the lower arms to the axle mounting points. FRONT SPRINGS: (pics soon) This is the ... (more)
Posted : 19 May 2005  
 
Loosing your Modular Mustang keys
Model : Ford, Mustang Category : Misc
... 1 key for duplication and it can be duplicated by a locksmith with the right electronic equipment. Even road side. 2) If your car is under warranty, Ford will pay to tow your car if you lose your keys. But only to the nearest dealer. And you have to pay for replacement of the lost key. 3) 98 to current year Mustangs require TWO keys to make a duplicate. And as mentioned above, you must take it ... (more)
Posted : 19 May 2005  
 
Low Budget PBR brake upgrade
Model : Ford, Mustang Category : Brakes
... Most take-off units come loaded with pads and brake lines. The '94+ Mustang brake lines are side specific, so you cannot switch sides with them. The '99+ Mustang lines are a direct bolt in for the 94-98 cars. The 94-95 spindles will have to be cleareanced for the dual piston 99+ calipers to work. To mount the PBR calipers on the older '94-98 spindles, you need to shave about 5mm off each ... (more)
Posted : 19 May 2005  
 
Let's fix an e36 Comfort Relay
Model : BMW, 3 - Series (E36) 1991-99 Category : Misc
... that the side towards the drivers door has some plastic clips. They'll unsnap cleanly if you don't try to force them. See pic below. Now the only thing holding the trim panel in is the 2 sets of wires plugged into the bell / buzzer module. Unplug these by squeezing the clips together. Don't worry about keeping track of which is which; one has 3 wires in it and the other has 4. Now right under ... (more)
Posted : 18 May 2005  
 
Lets Double Up the Brake Lights on My '95 ti
Model : BMW, 3 - Series (E36) 1991-99 Category : Misc
... it was a matter of selecting the proper placement of the holes for the ring connectors and the wire route. The photo shows exactly the conductors to jumper, and the two sides are a mirror image of each other. The wire was less than 4" in length with a ring connector at each end. I used the crimp type connectors. I made two of these and then set up for the drilling. Because of the way ... (more)
Posted : 18 May 2005  
 
Locked Doors
Model : BMW, 5 - Series (E34) 1989-96 Category : Exterior - Doors
... second car or battery - starting cable (i do not know if it is the correct english word) - a extra hand Place the minus on the engine (crawl under the car). On the driver side is the alternator, take the rubber seeling of and place the plus on it. (same can be done with the starter) Let the second person open the door. How To Open A Deadbolted Door: ( Procedure courtesy of Russell Jones ) Just ... (more)
Posted : 9 December 2004 Author : Bill R.
 
Lights Protection
Model : BMW, 5 - Series (E34) 1989-96 Category : Lights - Fog Lights
... (not hot), or use a heat gun or hair dryer to gently warm the light lens. Warm the cover too. 3. Before removing the backing paper, dry fit the cover on the lens. Wet your fingers into the glass with the solution (handling the parts with dry hand will leave marks). Remove the backing paper and immediately spray the solution to the exposed adhesive side and to the light lens. 4. Apply the ... (more)
Posted : 6 December 2004 Author : bmwe34.net
 
Leather Treatment
Model : BMW, 5 - Series (E34) 1989-96 Category : Interior - Seats
... or with a soft Terry Cloth towel and massage out the dirt. 5. Using 300 grit, lightly wet sand the leather to smooth out any cracks and hangnails in the surface, and to remove the surface of the old dye and as much of the old dye that is loose and worn from age. Do not attempt to cover over damaged dye. 6. Apply another coat of Rejuvenator as the seats will absorb it right away. 7. Apply the ... (more)
Posted : 3 December 2004 Author : George
 
LKM & Relay
Model : BMW, 5 - Series (E34) 1989-96 Category : Lights - Headlights
... your lights - hopefully the intermittent operation is a fading memory... Jason tried the relays only and it didn't work he said that all solder connections on the thrid of the PC board need to be heated up and new solder added. Procedure "Mustard" relay: E32 ONLY 1. The Mustard relay has retaining pins engaged in metal clips on the sides facing the wheels - they need to be pried off the pegs on ... (more)
Posted : 2 December 2004 Author : Max Fretter
 
Lets Double Up the Brake Lights on My '95 ti
Model : BMW, 3 - Series (E36) 1991-99, 318ti Category : Lights - Tail lights
... The photo shows exactly the conductors to jumper, and the two sides are a mirror image of each other. The wire was less than 4" in length with a ring connector at each end. I used the crimp type connectors. I made two of these and then set up for the drilling. Because of the way the conductors are attached to the plastic assembly, you cannot remove the conductors, so you must be VERY ... (more)
Posted : 14 May 2004 Author : Bob Collins
 
Browse by title :
# | A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z
Browse by make :
A | B | C | D | E | F | G | H | I | J | M | N | P | S | T | V