Working on the new Corvette Part 2: Computer diagnostics, driveline fluid checks, brakes and performance enhancements
Model : Chevrolet, Corvette Category : Misc
... a reduction in friction, the real advantage is a synthetic's ability to lubricate better at high temperatures. The C5 axle is packaged tightly and flanked by two hot exhaust pipes. Axle cooling, especially on hot days on the autocross or road race track is going to be at a premium. Perhaps a synthetic lubricant is a good choice. Red Line includes 6% friction modifier in their formula so ... (more)
Posted : 10 June 2005  
 
Working on the new Corvette Part 1: Engine issues and proper jacking
Model : Chevrolet, Corvette Category : Misc
... tools, will be releasing a device designed to address problems with lifting C5s with hoists. It will be similar in concept to the blocks we made but will twist-lock into to the shipping slots. If you are lifting a C5 with a twin-post, suspension contact hoist; position the front lift such that it catches the outboard ends of the front lower control arms just inboard of the lower ball joints. ... (more)
Posted : 10 June 2005  
 
Washer Nozzle Adjustment
Model : Audi Category : Exterior
... around in the socket to aim the jet of fluid to the desired location on the windshield. Remember when doing the adjustment(s) that the car will usually be moving. I always adjust the aim just a little high so that when I'm driving the fluid will hit the windshield in the correct location. Obviously, you cannot account for all speeds but with some common sense you can find a good compromise. ... (more)
Posted : 7 June 2005  
 
Window Guide Replacement
Model : Audi, A6 Category : Interior
... harness, power mirror, heated mirror, power window harness. 9. Unclip the wiring from the door panel as much as possible. 10. Mark the 4 T-45 bolts and shims. (one in each corner) 11. Remove 4 bolts holding in the inner frame. They may be slightly different, if so make sure to note where each goes. 12. Pull straight up on the frame. the entire assembly comes out including the mirror and upper ... (more)
Posted : 7 June 2005  
 
Wiper Arm Reversal
Model : Porsche, 911 - Series Category : Misc
... reverse the 914s wiper location.After listening to the pros and cons of reversing the wipers I decided to do mine only because I like the way they look and the clear view I have of the road. The following is a short pictorial of this project.[Click on Image to Enlarge]BeforeAfterDrivers ViewPull back the trunk carpet and remove the 4 bolts that secure the panel in front of the instruments.Remove ... (more)
Posted : 5 June 2005  
 
Wheel Painting
Model : Porsche Category : Wheels and Tires
... and smooth it gently but firmly. Don't press hard, or when you remove it, you'll pull up some of the silver. After masking the edge, then mask over the rest of the area. Step 8. Then, rinse the floor down gently with water. It will help keep the dust down when you paint. Spray your color coat according to manufacturer's instructions. I used a custom mix PPG color to match my sidestripes and ... (more)
Posted : 1 June 2005  
 
White Gauge Cluster
Model : Mazda, RX, RX - 7 Base Category : Misc
... I got them. The first step is to remove the old gauges. There are a few screws underneath the ignition plastic cover that need to be removed, along with the 4 screws under the windshield wiper switch and the headlight switch. Then remove the 3 screws from the underneath of the lip that overhangs the gauge cluster. Now remove the cluster cover. It should look like the below picture at this ... (more)
Posted : 25 May 2005  
 
Water Pump Replacement
Model : Mazda, RX, RX - 7 Base Category : Engine - Cooling System
... are $10 a piece from Mazda. Also now that the water pump housing is away from the block, you can unplug the water temp sensor behind it. Make sure not to loose the wire clip that is on the connector. Now is the time to remove the old water pump from the pump housing. Go ahead and set it aside as you will not need it any longer. Now comes the hardest part: removing the old gasket from the housing ... (more)
Posted : 25 May 2005  
 
Wheel Bearing Inspection/Adjustment
Model : Mazda, RX, RX - 7 Base Category : Wheels and Tires
... Bent the cotter pins legs back so you can remove it from the hub. Once that is finished, put it aside in a clean area. Once the set cover and cotter pin are off, you should just have the nut left. Try to twist it with your fingers. If you can do that, it is really loose. Either way...Get a torque wrench! or the next step, you will need a 23MM socket. *If you want to clean out the bearing grease ... (more)
Posted : 25 May 2005  
 
Water in rear floor of convertibles
Model : BMW, 3 - Series (E30) 1983-93 Category : Misc
... soaked?), as much trim as I could easily remove and finally I folded the carpet up out of the back floorboard. After this I stuffed paper towels around anywhere it looked like water may have come from I paid special attention to the backseat area since the underside of the backseat was wet. When I started spraying water I did not notice anything getting in. After a few seconds however I ... (more)
Posted : 24 May 2005  
 
Water leaks under the dashboard
Model : BMW, 3 - Series (E30) 1983-93 Category : Misc
... lamp -- if the rubber drain hose is not in place, you will have a bathtub in your trunk!).Then I removed the two black plastic grilles just forward of the windshield wipers and cleared debris from the drain in the corner and the drain on the firewall (which you access from the engine bay).This did the trick!I hope that this helps. Joel Barries Back SECTIONS :: Audio :: Body :: Brakes :: ... (more)
Posted : 24 May 2005  
 
Water leaks in the rear floorboard
Model : BMW, 3 - Series (E30) 1983-93 Category : Misc
... the rocker.BTW, My car took on water once more after this. It happened when my car was parked with the front down a VERY steep hill. The problem was the "fore" drain is located about 8 to 10 inches from the end of the rocker. This allows water to pool up and spill over before it reaches the drain.This phenomenon was immediately remedied with a 1/4 drill bit!!Some more details on the ... (more)
Posted : 24 May 2005  
 
Water leaks in the trunk
Model : BMW, 3 - Series (E30) 1983-93 Category : Misc
... window. The water would drip onto the metal that forms the deck support and either run forward on the wheel well into the interior, or rearward under the trunk liner on track into the rear jack well. Removal of the widow gasket itself revealed that the gasket was wet in the center from an area about half-way up the rear window, down to the horizontal part of the gasket. The water was obviously ... (more)
Posted : 24 May 2005  
 
Wheels and Tires
Model : Ford, Focus Category : Wheels and Tires
... TF Decals >>> TF Staff Directory Wheels and TiresRemovalCAUTION:Do not use heat to loosen a seized wheel nut. Heat may damage the wheel and wheel hub.1. Loosen the wheel nuts.2. Raise and support the vehicle. For additional information, refer to Section 100-02.3. Remove the wheel and tire assembly.Installation1. WARNING:Remove the corrosion or dirt from the mounting surfaces of the ... (more)
Posted : 20 May 2005  
 
Wheel vs. Tire width selection chart
Model : Ford, Mustang Category : Wheels and Tires
... 245/45R16 8.0-9.5 215/45R17 7.0-8.5 235/45R17 8.0-9.5 255/45R17 8.5-10.5 50 Series 175/50R13 5.0-6.0 195/50R14 5.5-7.0 205/50R15 5.5-7.5 215/50R15 6.0-7.5 225/50R15 6.0-8.0 195/50R16 5.5-7.0 205/50R16 5.5-7.5 225/50R16 6.0-8.0 235/50R16 6.5-8.5 215/50R17 6.5-7.5 55 Series 205/55R14 5.5-7.5 185/55R15 6.0-6.5 195/55R15 5.5-7.0 205/55R15 5.5-7.5 205/55R16 5.5-7.5 225/55R16 6.0-8.0 Aspect Ratio ... (more)
Posted : 19 May 2005  
 
Water temp & oil gauge install
Model : Ford, Mustang Category : Interior
... a stock look. I drilled two 2" inch holes to accommodate the gauges (could easily fit 3). After drilling the holes I glued the black vinyl to the acrylic pod using 3M spray glue (Home Mart or Home Depot). To fit the vinyl to the circumference of the holes, I performed 5 series of radius cuts to it, and then glued each slice to the pod. Make sure you leave about 1-2 mm un-cut to take into ... (more)
Posted : 19 May 2005  
 
Wrapping the Cross-Over Pipe
Model : Pontiac, Grand Prix Category : Engine - Cooling System
... and held in place by a metallic retaining strap (like the kind that holds the hose to the back of the clothes dryer), and looped all the way to the end of the crossover tube's length, where another retaining strap holds it all in place. Total installation time is around 15 minutes with 2 people doing it (one pulling the excess wrap and one doing the wrapping). I initially hear that this mode ... (more)
Posted : 19 May 2005  
 
Window Motor Repair
Model : BMW, 3 - Series (E36) 1991-99 Category : Interior - Windows
... warming up. __________________ ''Oh, Jason, take me!'' she panted, her breasts heaving like a student on 31p-a-pint night.'' -Bungy. 1992 325i Sedan - Bilstein HDs, M3 exhaust, SS brake lines, M3 shifter - 268000+ miles and going strong! 2000 323iT Wagon - E36 328i shifter in an E46... bungy42 View Public Profile Send a private message to bungy42 Send email to bungy42 Find all posts by bungy42 ... (more)
Posted : 18 May 2005  
 
Washing Your Car
Model : BMW, 3 - Series (E36) 1991-99 Category : Misc
... good 100% cotton terry towels. Make sure the towels have been washed once and do not use a rinse of softener on them. The rinse is an additive that can cause streaks, and retards absorbency of the towel. Using a rinse is not detrimental by any means, just a nuisance you learn to avoid. If I have been using my Porsche 911 for tours, rallies or in the rain there is usually some road grime. I use ... (more)
Posted : 18 May 2005  
 
Wheel Curb Rash removal
Model : BMW, 3 - Series (E36) 1991-99 Category : Wheels and Tires
... I feathered the edges to get a good blend. At first I used the paint thinner to clean some of the feathering (on the wheels, not the sparrow) but ultimately it was far superior to leave it feathered. So I left it to dry for a good cople of hours heeding NASA'a warning about the clear coat lifting the silver. (I chose to go sailing for a few hours, use this time wisely) I applied numerous ... (more)
Posted : 18 May 2005  
 
Washing Your Engine Part 1
Model : BMW, 3 - Series (E36) 1991-99 Category : Misc
... engine cleaner and spray it liberally in the areas of the engine that have the most built up grease on them. Let the engine cleaner soak for a few minutes, it will start eating away at the grease and dirt. Depending on how bad the build up is, this can take anywhere from a few minutes to 20 minutes. You probably will not get it all this first go around, so keep that in mind. While the engine ... (more)
Posted : 18 May 2005  
 
Washing Your Engine Part II
Model : BMW, 3 - Series (E36) 1991-99 Category : Misc
... up more "stuff" and remove the oily sheen from the metal. This is probably the most gratifying part of the job. The metal gleans and you can wipe you fingers along there and not have to wear gloves. If your metal paint is in bad shape, you may want to entertain the thought of painting it. This is what we did, however you have to take the engine out in order to do it properly. You ... (more)
Posted : 18 May 2005  
 
Welding Review
Model : BMW, 3 - Series (E36) 1991-99 Category : Misc
... button (also, the tip will have a gas outlet if your MIG uses tanks). When you press the button, wire (and gas, with a MIG with tanks) will be fed from a spool in the machine through the feed line and to the handle you hold in your hand and, as importantly - electricity will flow from that electrode. Don’t touch it when the button is on! Just a short note about the different types of MIG ... (more)
Posted : 18 May 2005  
 
Winter Hints & Tips
Model : BMW, 3 - Series (E36) 1991-99 Category : Misc
... traction therefore. My friend has a special Austrian model of the 524td where there are actual lead mats welded on the trunk and spare wheel compartment floors.2. Once you get stuck, you can use the sand to gain traction to your rear wheels.Sand will suck in moisture from your -probably leaking - trunk.Sand is a 100% natural eco product so for once your automotive hobby won't pollute the ... (more)
Posted : 18 May 2005  
 
Working MPG gauge for 318ti 6 cylinder conversions
Model : BMW, 3 - Series (E36) 1991-99, 318ti Category : Misc
... steering is nice just making it easier to replace the cluster bulbs. __________________ ...steven www.318ti.org National Capital Chapter, BMW CCA 1996 328ti View Public Profile Send a private message to 1996 328ti Visit 1996 328ti's homepage! Find all posts by 1996 328ti Add 1996 328ti to Your Buddy List Add 1996 328ti to Your Ignore List #3 09-11-2004, 11:44 PM carstereopro Member Join Date: ... (more)
Posted : 18 May 2005  
 
Wiring Radar detector to Sunroof switch
Model : BMW, 3 - Series (E36) 1991-99 Category : Electrical
... 7.If you want to make your life easy, buy little tiny wire nuts. I tried soldering, that was a bitch and it was to cold for electrical tape. you will have very short wires to work with, so don't strip off to much insulation. Also your Radar dectector wires will be so thin the will need to be doubled up to work with the wire connector. 8. After its all wired check to see that your detector ... (more)
Posted : 18 May 2005  
 
Window Motor Repair W/pics
Model : BMW, 3 - Series (E36) 1991-99 Category : Interior - Windows
... warming up. __________________ ''Oh, Jason, take me!'' she panted, her breasts heaving like a student on 31p-a-pint night.'' -Bungy. 1992 325i Sedan - Bilstein HDs, M3 exhaust, SS brake lines, M3 shifter - 268000+ miles and going strong! 2000 323iT Wagon - E36 328i shifter in an E46... bungy42 View Public Profile Send a private message to bungy42 Send email to bungy42 Find all posts by bungy42 ... (more)
Posted : 18 May 2005  
 
When are tires wornout ?
Model : All Makes Category : Wheels and Tires - Tires
... Of course these are tires not mattresses, and Costco not Montgomery Wards, so if anyone wants to do some relevant research I'd be thrilled to hear your results. How do I choose a tire? This answer will focus on how to purchase a passenger car tire since that is all we sell at Art's. If you want a non-stock performance tire or large truck tire then you should go to a shop with a working ... (more)
Posted : 18 May 2005  
 
What maintenance items are necessary to keep your car running reliably
Model : All Makes Category : Misc
... and fill. If the transmission fluid does go too long between changes, the transmission fluid can be flushed (all of the fluid is replaced with one visit using a flushing machining). However, this is 5 times the cost of a drain and fill and the transmission may be damaged from the time spent driving around with the bad fluid. So the best policy is to keep the ATF changes on a regular ... (more)
Posted : 18 May 2005  
 
What is a check engine light ?
Model : All Makes Category : Engine
... to get a better idea where to start looking for the problem. For instance, if there were a "code 1" on an older Honda, the mechanic would know to check for problems with the O2 sensor, wiring, or other problems that might affect output of the O2 sensor, like a misfire. On 1996 and newer cars the computer stores a lot more information, much like the "black box" flight ... (more)
Posted : 18 May 2005  
 
What Will Break
Model : BMW, 5 - Series (E34) 1989-96 Category : Misc
... pump 12. Doors restraint (the metal bar that stops the door from opening too far) is attached to the very thin metal of the door frame and is starting to fatigue and crack. 13. Gauge cluster, usually capacitors repair for 5.00in parts or purchase 750.00 rebuilt unit. 14. Steering box, excessive play on center, sometimes just an adjustment. 15. Light control module (LKM) repair or replace. ... (more)
Posted : 15 February 2005 Author : Bill R.
 
Winter Driving
Model : BMW, 5 - Series (E34) 1989-96 Category : Misc
... in your car. 8. Keep some none perishable food and bottled water. Exterior: 1. Thoroughly clean and wax the E34 (some people recommend using an acrylic sealant instead of wax for extreme winter condition). 2. Lubricate doors, hood and trunk latches. 3. Check the undercarriage and apply rubber, or asphalt undercoating, in damaged areas. 4. Spray the alloy wheels with silicone spray to protect ... (more)
Posted : 10 December 2004 Author : bmwe34.net
 
Winter Tires
Model : BMW, 5 - Series (E34) 1989-96 Category : Wheels and Tires - Tires
... don't expect miracles... Tires rated excellent in snow: - Bridgestone Blizzak - Michelin Pilot Alpin - Pirelli Asimmetrico Ice - Nokia NR09/NR10 - Pirelli Winter S2 - Continental Contact TS-740 - Goodyear F32S Don't forget to check your tire pressure. Optimum Winter Tire/Wheel Size: 215/60-15 225/60-15 205/65-15 215/55-16 225/55-16 Basically, this means you’re equipped with a narrower, higher ... (more)
Posted : 10 December 2004 Author : bmwe34.net
 
Winter Storage
Model : BMW, 5 - Series (E34) 1989-96 Category : Misc
... grease to rubber weather-strips all around. 4. Cedar board might help to prevent insects. 5. Close all vents. Battery: 1. Remove the battery and store it in a warm place. 2. Set it on a piece of wood (to avoid power drainage), away from open flame, sparks or... children. Tires: 1. You might want to remove the tires to remove the weight of the car. 2. Place all four corners of your E34 on ... (more)
Posted : 10 December 2004 Author : bmwe34.net
 
Wider Grill
Model : BMW, 5 - Series (E34) 1989-96 Category : Exterior
... the components of the grill and the hood then you will have to have the hood and the grill frame painted. Procedure GRILL ($200 aftermarket): • Grill frame: 51 13 8 170 096 • Grill cover over lights L/R: 51 13 8 148 311/312 • Center grill (kidney): 51 13 8 148 727 • Chrome pieces over kidney L/R: 51 13 8 148 725/726 • Frame fixing clamps L/R 51 13 1 978 151/152 Hood wide (Europe): ... (more)
Posted : 9 December 2004 Author : bmwe34.net
 
Wheels
Model : BMW, 5 - Series (E34) 1989-96 Category : Wheels and Tires
... strut towers). Micah O'C. used the same size wheels and tires Brigestone KDWS's. They rubbed the front strut towers enough to remove some paint and some of the lettering from the tires. A small spacer might be required depending on E34 model and tire choice. 5 mm spacers are not hubcentric and may cause some shimmy. A 10mm hubcentric spacer will probably work and will reduce the likelihood of ... (more)
Posted : 9 December 2004 Author : Stewart E, Sean Horton and Drew Z.
 
Window Motor Repair
Model : BMW, 3 - Series (E36) 1991-99 Category : Interior - Windows
... again. the object here is to lock the base of the gear you see in black to the black disk it sits on. Normally the gears base would have the black pressure disk attached, but it is eroded. I will post a pic later of how i lock the units together once i m done. Since we do not have a slipper clutch anymore, we do not need the rubber disk the gear base sits on. so let's just remove it. The ... (more)
Posted : 1 November 2004 Author : one
 
Browse by title :
# | A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z
Browse by make :
A | B | C | D | E | F | G | H | I | J | M | N | P | S | T | V